Plumbing Basics: Before Bathtub Installation
Plumbing Basics: Before Bathtub Installation
Blog Article
In this article in the next paragraph you can find more reliable facts pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Installing a bath tub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately tough project. If the old tub is conveniently available, the task can move immediately; if you need to open a wall to get rid of the old tub as well as place the brand-new bathtub, the task is a lot harder. In either case, the project is within a residence handyman's abilities, although you will need an assistant to vacate the old tub and also set in the new one. See to it you have actually certified on your own for the work and also fit trying it. Rather than hiring a professional to take over a halfway-completed job, it is better to think about employing one before you start. Opportunities are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your washroom if you have actually already bought a brand-new tub and do not need to change the setup of your previous water system pipes.
Your devices and product checklist should make up the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you must do is disconnect the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The process of removing the existing taps can be rather bothersome as a result of the restricted access that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming throughout this procedure. As soon as the taps have been removed, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to carrying on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washing machines remain in place between the tap and the sink. Secure the tap in place with the producer supplied backnut. When the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former type should be attached to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of the two wooden boards under its feet, position the tub in the required setting. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 small factors.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by checking the level and also adjusting the feet on the tub till the spirit level checks out degree.
To install taps, fit all-time low of the furthest adaptable faucet connector to the proper supply pipeline by making a compression join; then do the same for the other faucet.
Switch on the water system as well as check all joints and also new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as also inspect the overflow electrical outlet as well as the regular outlet for leakages.
Finally, repair the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub needs to wait until the tub has actually been made use of at least once as this will resolve it into its last position.
Getting ready for the Installation
First of all, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to prevent stress on the tub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture a stiff seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, bring about problems with wetness and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components and also installations. They are sold in tubes and cartridges, as well as are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of drenched paper or soft rope. Remember to constantly fill up the bath tub with water prior to sealing, to permit the movement experienced when the tub is in use. The sealant can crack rather very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed our part about How to Install a Bathtub. Thanks a ton for taking a few minutes to read our short article. Sharing is nice. Helping others is fun. We take joy in reading our article about Tools You Need to Install a New Bathtub .
Professional approach assured. Report this page